![]() ![]() ![]() Note: If you are not automatically directed to NETGEAR genie, launch a web browser and enter in the address field.This information applies to the Netgear model WGR614 v6. The browser takes you directly to NETGEAR genie smart setup. Open a web browser window from the same computer or mobile device. Use a WiFi network manager on a computer or mobile device to find and connect to the extender WiFi network.Īfter the connection with the computer or mobile device is established, the Client Link LED lights solid green.Ģ. To connect with the browser-based Smart Setup:ġ. You can use a web browser to connect to the extender and set it up. Use the Router Link LED on the front panel to help you choose a spot where the extender-to-router connection is optimal. If the Power LED does not light, press the Power button.ħ. Plug the extender into an electrical outlet and wait one minute. The location that you choose must be within the range of your existing WiFi router network.Ħ. Unplug the extender and move it to a new location closer to the area with a poor WiFi signal. Use the same WiFi password that you use for your WiFi router.ĥ. Connect your existing WiFi devices to the new extended network. The extender’s wireless network name (SSID) changes to your existing WiFi network name, with _EXT at the end of the name. On your computer or wireless device, find the new extender network name. If it still does not light, see Connect with NETGEAR genie Smart Setup on page 10.ģ. Note: If the Router Link LED does not light, try again. The WPS LED on the extender lights solid green, the Router Link LED lights, and the extender is connected to your existing WiFi network. Within two minutes, press the WPS button on your router or access point. Press the WPS button on the side panel of the extender. If you are using WEP security, see Connect with NETGEAR genie Smart Setup on page 10.ġ. WPS does not support WEP network security. The WPS button is a physical button on the router or access point. Wi-Fi Protected Setup (WPS) lets you connect the extender to a secure WiFi network without typing the network name and password. You can connect with WPS or with NETGEAR genie Smart Setup. To extend the range of your WiFi network, you must connect the extender to your existing WiFi network. If the Power LED does not light, press the Power button. Plug the extender into an electrical outlet. Place your extender in the same room as your WiFi router.Ģ. Then move it farther away from the router as needed to increase the area that has a WiFi signal.ġ. NETGEAR recommends that you place the extender near the router during initial setup. If no arrow LEDs are lit, the extender is in a good location. ![]() If the Router Arrow or Client Arrow LED blinks, see Find the Best Location on WiFi security is enabled (WPA or WPA2).īlinking green. The connection between the extender and a computer or mobile device. The connection between the extender and the router or access point. 32 Cannot Join the Extender WiFi Network. 27 View Wired and Wireless Network Devices. 25 Erase the Extender Settings and Return to Factory Settings. 25 Use the Factory Reset Button to Restore Factory Settings. 24 Return the Extender to Its Factory Settings. 22Ĭhapter 4 Monitor and Maintain the Extenderīack Up the Extender Configuration. 20 Set Up the Extender to Use a Static IP Address. 18 View or Change Advanced Wireless Settings. 16 Add a WPS Client to the Extender Network. 15 Use the Setup Wizard to Connect the Extender to a Network. Log In to the Extender After Initial Setup. 13Ĭhapter 3 Manage the Extender Network and Settings 12 Cable a Computer or Device to the Ethernet Port. Information is subject to change without notice.įront Panel. ![]() and/or its subsidiaries in the United States and/or other countries. NETGEAR, the NETGEAR logo, and Connect with Innovation are trademarks and/or registered trademarks of NETGEAR, Inc. See the regulatory compliance document before connecting the power supply. įor regulatory compliance information, visit. Phone (Other Countries): Check the list of phone numbers at. For product updates and web support, visit. NETGEAR recommends registering your product through the NETGEAR website. You must register your product before you can use NETGEAR telephone support. Thank you for selecting NETGEAR products.Īfter installing your device, locate the serial number on the label of your product and use it to register your product at. ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |